Tree Felling and Dismantling
This is where the complete removal of a tree to ground level is required. Usually a tree must be dismantled in stages by a climber using a combination of techniques to ensure a safe and damage free process.
Smaller trees can be straight felled if the surroundings allow. All stumps are left at ground level and can be poisoned or stump grinded if required.
This is the pruning, usually of young to Semi mature tree and shrubs to help them develop a good strong healthy structure or form. It usually entails removal of crossing and competing branches or a secondary leader. This process may need to be repeated several times while a tree is getting established. Good proactive formative pruning can save the need for more expensive, invasive ‘tree surgery’ later in the trees life.
This is the selective removal of branches to reduce the density of the tree. It should be achieved by removal of branches from throughout the crown (not only from the inner crown) to leave a crown with a balanced density, but no more than 30% of the foliage should be removed in a single year, as this may cause the tree stress. The minimum number of branches should be removed to achieve the desired effect. Crown thinning on a smaller tree may be undertaken as part of the formative pruning, but on a larger tree may be specified for other reasons:
When to crown thin a large tree:
- To allow more light through the crown, reducing the density of the shade beneath the tree.
- To allow the wind to percolate through the crown, therefore reducing the likelihood of wind throw.
When not to crown thin a large tree:
- Crown thinning certain species has the effect of making the produce more growth along the branches, at best undoing the recent thinning and at worst making the crown denser than before you started. This can certainly be a risk with Limes, Maples and to a degree Oaks.
- Where a tree is already unstable due to a defect at the base or due to soil/root movement. In this instance a crown reduction may be more appropriate.
Crown reduction / reshaping
This is where the crown of the tree is made smaller, either all over or in a certain area to redress an imbalance of the shape. As with crown thinning no more the 30% of the foliage should be removed in one year and the out-come should be to leave the tree looking as natural as possible and not leaving large thick branch ends on the extremities of the crown. A good reduction/reshaping will leave the tree with a strong framework of large branches, which support enough smaller branches and twigs (leaf bearing material) capable of producing dense leaf coverage next season.
When to crown reduce/reshape:
- When a tree has become too large for its position, but removal of the tree is undesirable.
- When the stability of the tree is in question due to defects or movement in the ground.
- To address an imbalance or to prune to clear an object (e.g. building or street light).
- To maintain a specific crown shape (e.g. Pleached trees).
When not to crown reduce/reshape:
- Certain species react poorly to reductions, conifers in general (apart from hedges) do not reshape well and often look poor afterwards, and Maples especially will put on vigorous regrowth and become overly dense due to this growth.
- When a tree is obviously the wrong tree for its position, it may be best to remove it and start again with a more suitable tree.
This is the removal of the lowest branches to a specified height and where possible should be achieved by removal of smaller branches so to minimise stress to the tree. The crown of the tree should not be lifted to a point which is more than 1/3 of the overall tree height (i.e. leaving 2/3 of the trees height as crown).
When to crown lift:
- To open a view or allow more light under the crown, this can often be more effective in increasing light level when the tree is close to where you need the light (reduction works are more suitable when the tree is further away).
- To separate a tree’s canopy from the ground, this can be to create space, make mowing easier or to improve the look of the tree (it can make a tree look more grand).
When not to crown lift:
- When the tree already has a high crown.
- When to achieve this large branches will need to be removed, this can store up problems for the future.
This is the removal of unwanted material form the crown of the tree and may include some crown thinning, it would also include the removal of climbing plants (ivy etc) foreign objects (old tree houses, shopping trolleys etc) and parasitic plants like Mistletoe.
A true pollard is a tree that has been cut back as a young tree and then repeatedly pruned to the same point creating a pollard knuckle. The term is often used (technically incorrectly) to describe a heavy reduction of a larger tree, which is then to be managed in the future as a pollard. This approach can work for certain species of trees and your Arborist should be able to advise you on this and explain the management regime that will be required afterwards.
This is generally the removal of the soft outer growth using a mechanical hedge trimmer. This method can be used on hedges, shrubs or trees and is generally repeated at least once a year.